KINITSection: User Commands (1)
Index Return to Main Contents
NAMEkinit - obtain and cache Kerberos ticket-granting ticket
[-l lifetime] [-s start_time]
[-p | -P]
[-f | -F]
[-k [-t keytab_file]] [-c cache_name]
[-S service_name][-T armor_ccache]
DESCRIPTIONkinit obtains and caches an initial ticket-granting ticket for principal.
- display verbose output.
- -l lifetime
requests a ticket with the lifetime
The value for
must be followed immediately by one of the following delimiters:
s seconds m minutes h hours d days
as in "kinit -l 90m". You cannot mix units; a value of `3h30m' will result in an error.
If the -l option is not specified, the default ticket lifetime (configured by each site) is used. Specifying a ticket lifetime longer than the maximum ticket lifetime (configured by each site) results in a ticket with the maximum lifetime.
- -s start_time
- requests a postdated ticket, valid starting at start_time. Postdated tickets are issued with the invalid flag set, and need to be fed back to the kdc before use.
- -r renewable_life
- requests renewable tickets, with a total lifetime of renewable_life. The duration is in the same format as the -l option, with the same delimiters.
- request forwardable tickets.
- do not request forwardable tickets.
- request proxiable tickets.
- do not request proxiable tickets.
- request tickets with the local address[es].
- request address-less tickets.
- requests canonicalization of the principal name.
- treats the principal name as an enterprise name.
- requests that the ticket granting ticket in the cache (with the invalid flag set) be passed to the kdc for validation. If the ticket is within its requested time range, the cache is replaced with the validated ticket.
- requests renewal of the ticket-granting ticket. Note that an expired ticket cannot be renewed, even if the ticket is still within its renewable life.
- -k [-t keytab_file]
- requests a ticket, obtained from a key in the local host's keytab file. The name and location of the keytab file may be specified with the -t keytab_file option; otherwise the default name and location will be used. By default a host ticket is requested but any principal may be specified. On a KDC, the special keytab location KDB: can be used to indicate that kinit should open the KDC database and look up the key directly. This permits an administrator to obtain tickets as any principal that supports password-based authentication.
- Requests anonymous processing. Two types of anonymous principals are supported. For fully anonymous Kerberos, configure pkinit on the KDC and configure pkinit_anchors in the client's krb5.conf. Then use the -n option with a principal of the form @REALM (an empty principal name followed by the at-sign and a realm name). If permitted by the KDC, an anonymous ticket will be returned. A second form of anonymous tickets is supported; these realm-exposed tickets hide the identity of the client but not the client's realm. For this mode, use kinit -n with a normal principal name. If supported by the KDC, the principal (but not realm) will be replaced by the anonymous principal. As of release 1.8, the MIT Kerberos KDC only supports fully anonymous operation.
- -T armor_ccache
- Specifies the name of a credential cache that already contains a ticket. If supported by the KDC, This ccache will be used to armor the request so that an attacker would have to know both the key of the armor ticket and the key of the principal used for authentication in order to attack the request. Armoring also makes sure that the response from the KDC is not modified in transit.
- -c cache_name
as the Kerberos 5 credentials (ticket) cache name and location; if this
option is not used, the default cache name and location are used.
The default credentials cache may vary between systems. If the KRB5CCNAME environment variable is set, its value is used to name the default ticket cache. Any existing contents of the cache are destroyed by kinit.
- -S service_name
- specify an alternate service name to use when getting initial tickets.
- -X attribute[=value]
specify a pre-authentication attribute and value to be passed to
pre-authentication plugins. The acceptable attribute and
value values vary from pre-authentication plugin to plugin.
This option may be specified multiple times to specify multiple
attributes. If no value is specified, it is assumed to be
The following attributes are recognized by the OpenSSL pkinit pre-authentication mechanism: X509_user_identity=value specify where to find user's X509 identity information X509_anchors=value specify where to find trusted X509 anchor information flag_RSA_PROTOCOL[=yes] specify use of RSA, rather than the default Diffie-Hellman protocol
ENVIRONMENTKinit uses the following environment variables:
- Location of the Kerberos 5 credentials (ticket) cache.
- default location of Kerberos 5 credentials cache ([uid] is the decimal UID of the user).
- default location for the local host's keytab file.
SEE ALSOklist(1), kdestroy(1), kerberos(1)
This document was created by man2html, using the manual pages.
Time: 05:29:05 GMT, December 24, 2015